![background image](http://html1.mh-extra.com/html/omron/c200hw/c200hw_operation-manual_742329087.webp)
4-2
Section
Common Parameters
74
Zone #0, CCW Side (Rightmost Word)
X axis 1660 (NC113), Y axis 2660 (NC213), Z axis 3660 and U axis 4660
(NC413)
Zone #0, CCW Side (Leftmost Word)
X axis 1661 (NC113), Y axis 2661 (NC213), Z axis 3661 and U axis 4661
(NC413)
Zone #0, CW Side (Rightmost Word)
X axis 1662 (NC113), Y axis 2662 (NC213), Z axis 3662 and U axis 4662
(NC413)
Zone #0, CW Side (Leftmost Word)
X axis 1663 (NC113), Y axis 2663 (NC213), Z axis 3663 and U axis 4663
(NC413)
15
00
Sign
x10
6
x10
5
x10
4
x10
3
x10
2
x10
1
x10
0
Leftmost word
00
15
Rightmost word
Designation for both CCW and CW sides
This sets the data for zone #0.
Sign:
0: Positive (CW); 1: Negative (CCW)
Range: -9,999,999 to +9,999,999 (pulses)
Make the settings so that the CCW value is less than the CW value.
Default Setting: 0000, 0000
Zone #1, CCW Side
X axis 1664 (NC113), Y axis 2664 (NC213), Z axis 3664 and U axis 4664
(NC413)
Zone #1, CW Side
X axis 1666 (NC113), Y axis 2666 (NC213), Z axis 3666 and U axis 4666
(NC413)
The settings are the same as for zone #1.
Default Setting: 0000, 0000
Zone #2, CCW Side
X axis 1668 (NC113), Y axis 2668 (NC213), Z axis 3668 and U axis 4668
(NC413)
Zone #2, CW Side
X axis 1670 (NC113), Y axis 2670 (NC213), Z axis 3670 and U axis 4670
(NC413)
The settings are the same as for zone #1.
Default Setting: 0000, 0000
4-2
Common Parameters
The common parameters are allocated to the Programmable Controller’s DM
area. The locations in the DM area are determined when the Position Control
Unit’s unit number is set.
The settings for the common parameters are explained below.
Note
1. The settings for the common parameters must be made when the PCU is
used. If these settings are not made, a common parameters error will be
generated (error codes 0010 to 0013) and the PCU will not operate nor-
mally.
2. After the common parameter settings have been made, they will go into
effect the next time the PCU is powered up or restarted.
Содержание C200HW
