Docomo PRIME series N-01A, Инструкция по эксплуатации

Страница: 585 / 602

36
AT&W
n
Stores the current settings. Only
n
= 0 can be specified (can be omitted). AT&W0
OK
AT&W
OK
AT&W?
ERROR
AT&W ＝ ?
ERROR
AT
＊
DANTE Displays the FOMA terminal
signal reception level.
0 ： FOMA terminal signal reception level is displayed as
out of area.
1
：
FOMA terminal signal reception level is 0 or 1
bar.
2 ： FOMA terminal signal reception level is 2 bars.
3 ： FOMA terminal signal reception level is 3 bars.
AT
＊
DANTE
＊ DANTE:3
OK
AT
＊
DANTE
＝
?
＊ DANTE:(0-3)
OK
AT
＊
DGANSM=
n
Sets the reject/permit mode
setting for the packet
incoming call. This
command is effective for
those incoming packet calls
after the setting command is
input. n
= 0
：
Disables the incoming call reject (AT
＊
DGARL)/permit setting (AT
＊
DGAPL) (initial
value).
n
= 1
：
Enables the incoming call reject
setting.
n
= 2
：
Enables the incoming call permit
setting.
AT
＊
DGANSM?
：
Displays the current setting.
AT
＊
DGANSM=0
OK
AT
＊ DGANSM?
＊ DGANSM:0
OK
AT ＊ DGAPL= n [,cid]
Sets APN, which permits
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
n = 0 ： Adds the APN defined by <cid> to
incoming call permission list.
n
= 1 : Deletes the APN defined by <cid>
from incoming call permission list.
If <cid> is omitted, this will apply to all cid.
AT
＊ DGAPL?
： Displays incoming call permission list.
AT ＊ DGAPL =0,1
OK
AT
＊
DGAPL?
＊
DGAPL:1
OK
AT
＊ DGAPL =1
OK
AT
＊
DGAPL?
OK
AT
＊
DGARL=
n
[,cid] Sets APN, which rejects
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
n
= 0 : Adds the APN defined by <cid> to
incoming call rejection list.
n
= 1 : Deletes the APN defined by <cid>
from incoming call rejection list.
If <cid> is omitted, this will apply to all cid.
AT
＊
DGARL?
：
Displays incoming call rejection list.
AT
＊
DGARL =0,1
OK
AT
＊ DGARL?
＊ DGARL:1
OK
AT
＊
DGARL =1
OK
AT
＊ DGARL?
OK
AT ＊ DGPIR=
n
This command validates the
setting for notifying Caller ID
when sending/receiving
packet communication.
Even in the dial up network
setting, you can also add
186 (notify) or 184 (not
notify) to the access point
number. (p.23)
n
= 0 : Uses APN as it is (initial value).
n
= 1 : Uses APN by adding "184". (Caller ID
is always not sent.)
n
= 2 : Uses APN by adding "186". (Caller ID
is always sent.)
AT ＊ DGPIR?
： Displays the current setting.
AT ＊ DGPIR =0
OK
AT
＊
DGPIR?
＊
DGPIR:0
OK
AT
＊
DRPW Displays the indicator value
of the receiving power of the
FOMA terminal. − AT
＊
DRPW
＊
DRPW:0
OK
AT ＊ DRPW=?
＊
DRPW:(0-75)
OK
AT+CAOC Inquires for the current
charge.
−
AT+CAOC
+CAOC:"000014"
OK
AT command Outline Parameter/description Command execution example