Docomo PRIME series N-01A, Инструкция по эксплуатации

Страница: 433 / 602

431 Continued on next page
Network Servic
es
*1 : Number A is dialed by default when using A/Common setting Phonebook, and Number B is dialed by default when
using B Phonebook.
*2 : If the phonebook call acception/call rejection is set, the call is accepted/rejected regardless of the mode you use
and phonebook 2in1 setting.
*3 : Priority is given to Secret data when the data is saved as secret.
*4 : In B mode, all phonebook entries in a microSD card are displayed in a list. However, the details are not displayed
when Phonebook 2in1 setting is set to A mode. Although mail/SMS are also listed, the details are not displayed if
the mail/SMS is sent to Number A/Address A.
*5 : This function checks with phonebook data and converts caller’s number, receiver’s number, sender’s number,
recipient’s number, sender’s address and recipient’s address into names in phonebook data.
*6 : “A” applies when the sender uses a 2in1-incompatible phone.
*7 : The recipient address can be selected from B setting Phonebook when composing a new mail in Dual mode. Note
that the mail is sent from Address A. Also note that if you forward mail sent to Address B in Dual mode, the mail is
sent from Address A.
*8 : Except for mail-linked i-
α
ppli, i-
α
ppli using the mail function and the i-
α
ppli standby screen.
*9 : Except for the i-
α
ppli standby screen.
Using 2in1
Set 2in1 to ON and configure settings.
1
i
X
“Settings/Service”
X
“Network service”
X
“2in1 setting”
X
Enter your security code
X
“YES”
X
Select any item:
■ When 2in1 is set to ON
After entering your security code, a screen does
not appear asking whether to set 2in1 to ON, but
the 2in1 setting screen appears.
Mode switching
……
Select A mode/B mode/Dual
mode. “Modes”
→
p.429
Phonebook 2in1 setting …… Set Phonebook 2in1
setting/Group 2in1 setting for the phonebook to
appear following the mode setting when in 2in1.
Highlight a phonebook entry or group and press
d
(Switch) to select a mode, then press
o
(Finish). Each time you press
d
(Switch), the
mode switches as follows: → →
Searching the phonebook → p.96
Stand-by display
……
Set the standby screen
displayed in B mode or Dual mode respectively.
→ p.113
“
★
” appears for the changed item. Press
o
(Reset) to reset the setting to default.
Set call/receive No.
Disp. call/receive No. …… Change font color to
distinguish between Number A (Address A) and
Number B (B address) (name, phone number,
mail address, etc.) when making/receiving a
call. Press
o
(Switch) to switch the pallet
colors (16 colors or 256 colors). Press
p
(Reset) to reset the setting to default.
Ringtone for Number B …… Set incoming
operations for Number B. In “Voice call (recv.)”
or “V.phone (recv.)”, the following
①
Ring tone,
② Image, ③ Illumination, ④ Vibrator and ⑤
Answer message can be set. In “Mail (recv.)”,
the following
①
Ring tone,
③
Illumination and
④ Vibrator can be set:
Voice call (recv.), V.phone (recv.), Mail
(recv.)
……
① Ring tone: Go to Step 2 in “Changing
the Ring Tone” (p.104)
②
Image: Go to “
■
To set the calling/
receiving display” under Step 2 in
“Changing the Ring Tone” (p.104)
③
Illumination: Go to Step 1 in “Setting
the Flashing Mode of the Incoming Call
Lamp for Incoming Calls” (p.118)
④
Vibrator: Go to Step 2 in “Setting the
Vibration to Notify You of Incoming
Calls” (p.106)
⑤ Answer message: Go to the step
performed after selecting “ON” under
Step 1 in “Setting Record message”
(p.78)
PushTalk Dial Number A Not available Number A
Receive
*2
Number A
PushTalk Display Cannot be displayed Display
i-
α
ppli All available Available
*8
Available
*9
My Profile Number A/Address A Number B/Address B Number A/B
Address A/B
Service A mode B mode Dual mode