Docomo PRIME series N-01A, Инструкция по эксплуатации

Страница: 481 / 602

479 Continued on next page
Appendix/Troublesho
oting
Mail ring tones and alarm tones sound, but no
ring tone sounds when a call or PushTalk arrives
●
Is “Set mute seconds” under “Ring time (sec.)” set to
long time (e.g. 99 seconds)? Set “Set mute seconds” to
shorter time.
→ p.146
The ring tone sounding when a voice call or
videophone call arrives is different from what I
selected
●
When the ring tone settings are duplicated, the priority
is assigned.
→ p.105
The image displayed when a voice call or
videophone call arrives is different from what I
selected
●
When the image settings are duplicated, the priority is
assigned.
→ p.105
When a voice call or videophone call arrives, the
color or pattern of the incoming call lamp flashing
is different from what I set up
●
When the illumination settings are duplicated, the
priority is assigned.
→
p.118
The screen or ring tone active for an incoming
call or mail is the default setting
●
Depending on the combination of receiving screen and
ring tone or the priority sequence, either the receiving
screen or ring tone may be restored to default.
●
When you set downloaded Flash movies as the receiving
display or received result screen for mail and set i-motion/
music for ring tones, the screen display may be restored
to default depending on the combination of receiving
screen and ring tone.
Receiving an incoming call immediately after
turning on the power displays the phone number
but does not display the name stored in the
phonebook
●
The FOMA card (UIM) may be being read immediately
after turning on the power. The phonebook function
may not be available then.
Talk
The other party’s voice is difficult to hear during a
call
●
Is the earpiece properly placed against your ear?
→ p.22
●
Is anything (e.g. a sticker) obstructing the earpiece?
●
Is anything obstructing the speaker in handsfree
mode?
●
Did you change the “Volume” setting?
Change the setting so that you can hear the other party
clearly.
→ p.74
The other party’s voice is too loud during a call
●
Did you change the “Volume” setting?
Change the setting so that you can hear the other party
clearly.
→ p.74
Sending/Receiving Mail (Ring Tone/
Image/Illumination)
The receiving message operations (ring tone
sounding, vibrator, incoming call lamp flashing)
are not performed when a mail arrives
●
Is “Mail/Msg. ring time” set to “OFF”? → p.108
●
Is Original lock for “Disp. recv. mail/msg.” under
“Incoming/Mail disp.” active?
→
p.139
●
Is “Receiving setting” set to “Operation preferred”?
→ p.181
●
Is the mail address or phone number of the third party
stored as secret data?
→
p.133
The ring tone sounding when a mail arrives is
different from what I selected for the mail address
●
When the ring tone settings are duplicated, the priority
is assigned.
→ p.105
●
If you have received multiple mail, the tone set for the
last received mail address sounds.
→ p.105
●
If you have received multiple mail including chat mail,
the ring tone set for the chat mail sounds.
→ p.105
●
If the format of the sender’s mail address is “phone
number@docomo.ne.jp”, save only that phone number
as a mail address and set a distinctive ring tone for that
mail address in “Ring tone” under “Mail (recv.)”.
→ p.99
●
Is the sender’s mail address (a mail address shown on
the received mail detail screen) stored in the
phonebook correctly and did you set a distinctive ring
tone for that mail address in “Ring tone” under “Mail
(recv.)”?
→
p.99
●
If you receive SMS, a distinctive ring tone set in “SMS
(recv.)” for the phone number in the phonebook
sounds.
→ p.100
The color of illumination flashing when a mail
arrives is different from what I selected for the
mail address
●
When the illumination settings are duplicated, the
priority is assigned.
→ p.118
●
If you receive multiple mail, the incoming call lamp
flashes following the settings of the “Illumination” under
“Mail (recv.)” that is set to the last received mail
address.
→ p.118
●
If the format of the sender’s mail address is “phone
number@docomo.ne.jp”, save only that phone number
as a mail address and set distinctive illumination for
that mail address in “Illumination” under “Mail (recv.)”.
→
p.99
●
Is the sender’s mail address (a mail address shown on
the received mail details screen) stored in the
phonebook correctly and did you set illumination for
that mail address in “Illumination” under “Mail (recv.)”?
→ p.99
●
If you receive SMS, distinctive illumination set in
“Illumination” under “SMS (recv.)” for the phone number
in the phonebook flashes.
→
p.100