Docomo PRIME series N-01A, Инструкция по эксплуатации

Страница: 480 / 602

478
Appendix/Troublesho
oting
Troubleshooting
z
Check first whether the software update is required. If necessary, update the software.
→
p.492
z
Problems are categorized. Color text indicates problems, and black text indicates the points to check and
reference pages.
Power/Battery
The power does not turn on (The FOMA terminal
cannot be used)
●
Is the battery pack properly attached? → p.50
●
Has the battery run out? → p.52
It takes some time to turn on the power after
pressing and holding
y
for 1 second or longer
●
Data checking may take time (e.g. if the phonebook is
full of data).
→ p.99
The animation shown on the right appears and an
alarm tone sounds
●
The battery has run out.
Recharge the battery.
→ pp.51, 53
Cannot charge the battery (the charge lamp does
not light)
●
Is the battery pack properly attached to the FOMA
terminal?
→
p.50
●
Is the adapter firmly plugged into the electrical outlet or
cigarette lighter socket?
→ p.52
●
Are the adapter and the FOMA terminal correctly
connected (is the AC adapter firmly connected to the
FOMA terminal or the desktop holder)?
→ p.52
Battery becomes low soon even when fully
charged
●
The battery life may soon be over. The battery life may
be shortened depending on the usage environment.
→ p.51
●
Battery time varies depending on usage. → p.51
Communication (Phone/i-mode
Connection)
“ ” appears and calls cannot be made
●
Are you out of range or is the reception poor? → p.54
Cannot make a call by pressing the dial keys
●
Is Original lock for “Keypad dial” under “Dial/sending
mail” set?
→
p.139
●
Is Keypad lock set? → p.140
●
Is Restrict dialing set? → p.144
I dialed a number and initiated a call, but all I hear
is a busy tone
●
Did you start dialing before hearing the dial tone?
→ p.58
●
Did you forget to dial the area code? → p.58
●
Is “Please wait” displayed?
i-mode, i-mode mail, i-
α
ppli and i-Channel cannot
be connected
●
Is “Host selection” set to other than “i-mode”? → p.208
●
If you had started using the FOMA terminal before you
subscribed to i-mode, turn the power off and then turn it
back on.
Receiving Calls (Ring Tone/Image/
Illumination)
Cannot receive calls or hear the ring tone
●
Are any of the following functions set?
Restrictions
→ p.144
• Call rejection • Call acceptation
• Call Forwarding • Voice Mail
Ring time (sec.)
→
p.146
• Set mute seconds
Reject unknown
→ p.147
Call setting w/o ID → p.146
• Unknown: Reject • Payphone: Reject
• User unset: Reject
●
In manner mode? → p.109
●
In Public mode (Driving mode)? → p.75
●
Is Original lock for “Incoming call” under “Incoming/Mail
disp.” active?
→ p.139
●
In Self mode? → p.147
●
Is the start time of Voice Mail or Call Forwarding
service set to “0 second”?
→
pp.422, 424
●
Is Caller ID Request set to “Activate”? → p.425
●
Is mova valid with the Dual Network service? → p.425
●
Is the ring volume set to “Silent”? → p.74
●
Is the ring time of Record message set to “0 second”?
→ p.78
The incoming call operations (ring tone
sounding, vibrator, incoming call lamp flashing)
are not performed when a call arrives
●
The incoming call operations (ring tone sounding,
vibrator, incoming call lamp flashing) are not performed
until the set time is reached, when a call arrives from a
phone number not stored in the phonebook or from a
caller who does not notify his/her caller ID and if “Set
mute seconds” under “Ring time (sec.)” is set to “ON”.
→ p.146