Omron SYSDRIVE 3G3RV, User Manual, Page: 440 / 446

Parameters
10-
17
10
L1-01 Motor
protection selection
1 L7-03 Forward
regenerative torque limit
200
L1-02 Motor
protection time constant
1.0 L7-04 Reverse
regenerative torque limit
200
L1-03
Alarm
operation selection during
motor
overheating
3 L8-01
Protect
selection for internal DB
resistor
0
L1-04
Motor
overheating operation selec-
tion
1 L8-02 Overheat
pre-alarm level
95
L1-05
Motor
temperature input filter time
constant
0.20 L8-03
Operation
selection after overheat
pre-alarm
3
L2-01 Momentary
power loss detection
0 L8-05
Input
open-phase protection selec-
tion
0
L2-02
Momentary
power loss ridethru
time
0.1
*6
L8-07
Output
open-phase protection
selection
0
L2-03 Min.
baseblock time
0.1 L8-09 Ground
protection selection
1
L2-04 Voltage
recovery time
0.3 L8-10 Cooling
fan control selection
0
L2-05 Undervoltage
detection level
190
*7
L8-11 Cooling
fan control delay time
60
L2-06 KEB
deceleration time
0.0 L8-12 Ambient
temperature
45
L2-07 Momentary
recovery time
0
*11
L8-15
OL2
characteristics selection at
low
speeds
1
L2-08
Frequency
reduction gain at KEB
start
100 L8-18 Soft
CLA selection
1
L3-01
Stall
prevention selection during
accel
1 N1-01
Hunting-prevention
function selec-
tion
1
L3-02 Stall
prevention level during accel
120 N1-02 Hunting-prevention
gain
1.00
L3-03 Stall
prevention limit during accel
50 N2-01
Speed
feedback detection control
(AFR)
gain
1.00
L3-04
Stall
prevention selection during
decel
1 N2-02
Speed
feedback detection control
(AFR)
time constant
50
L3-05
Stall
prevention selection during
running
1 N2-03
Speed
feedback detection control
(AFR)
time constant 2
750
L3-06
Stall
prevention level during run-
ning
120 N3-01
High-slip
braking deceleration fre-
quency
width
5
L4-01 Speed
agreement detection level
0.0 N3-02 High-slip
braking current limit
150
L4-02 Speed
agreement detection width
2.0 N3-03 High-slip
braking stop dwell time
1.0
L4-03
Speed
agreement detection level
(+/-)
0.0 N3-04 High-slip
braking OL time
40
L4-04
Speed
agreement detection width
(+/-)
2.0 o1-01 Monitor
selection
6
L4-05
Operation
when frequency refer-
ence
is lost
0 o1-02 Monitor
selection after powerup
1
L4-06
Frequency
reference for loss of fre-
quency
reference
80.0 o1-03
Frequency
units of reference set-
ting
and monitor
0
L5-01 Number
of auto restart attempts
0 o1-05 LCD
brightness
3
L5-02 Auto
restart operation selection
0 o2-01
LOCAL/REMOTE
key enable/dis-
able
1
L6-01 Torque
detection selection 1
0 o2-02
STOP
key during control circuit
terminal
operation
1
L6-02 Torque
detection level 1
150 o2-03 Parameter
initial value
0
L6-03 Torque
detection time 1
0.1 o2-04 kVA
selection
0
*6
L6-04 Torque
detection selection 2
0 o2-05
Frequency
reference setting
method
selection
0
L6-05 Torque
detection level 2
150 o2-06
Operation
selection when digital
operator
is disconnected
0
L6-06 Torque
detection time 2
0.1 o2-07 Cumulative
operation time setting
0
L7-01 Forward
drive torque limit
200 o2-08
Cumulative
operation time selec-
tion
0
L7-02 Reverse
drive torque limit
200 o2-09 Factory
use
-
Table 10.1 Parameters (Continued)
No. Name
Fac-
tory
Setting
Set-
ting
No. Name
Fac-
tory
Setting
Set-
ting