Mitsubishi Electric EZMotion-NC E60 Series, Operation Manual

Page: 474 / 510

Appendix 2. Table of Command Value Ranges
IV -2
Appendix 2 Table of Command Value Ranges
Linear axis Rotary axis
Input unit: mm Input unit: inch Degree (°)
Minimum input setting unit 0.001
0.0001
0.0001
0.00001 0.001
0.0001
Maximum stroke
(Value on machine
coordinate system) ±99999.999 mm
±9999.9999 mm ±9999.9999 inch
±999.99999 inch ±99999.999 °
±9999.9999 °
Maximum command value ±99999.999 mm
±9999.9999 mm
±9999.9999 inch
±999.99999 inch ±99999.999 °
±9999.9999 °
Rapid traverse rate
(Including during dry run) 1 to 1000000 mm/min
1 to 100000 mm/min 1 to 39370 inch/min
1 to 3937 inch/min 1 to 1000000 °/min
1 to 100000 °/min
M system cutting feed rate
(Including during dry run) 0.01 to 1000000 mm/min
0.001 to 100000 mm/min 0.001 to 39370 inch/min
0.0001 to 3937 inch/min 0.01 to 1000000 °/min
0.001 to 100000 °/min
L system cutting feed rate
(Including during dry run) 0.001 to 1000000 mm/min
0.0001 to 100000 mm/min 0.0001 to 39370.0787 inch/min
0.00001 to 3937.00787 inch/min 0.001 to 1000000 °/min
0.0001 to 100000 °/min
M system synchronous
feed 0.001 to 999.999 mm/rev
0.0001 to 99.9999 mm/rev 0.0001 to 999.9999 inch/rev
0.00001 to 99.99999 inch/rev 0.01 to 999.99 °/rev
0.001 to 99.999 °/rev
L system synchronous feed 0.0001 to 999.9999 mm/rev
0.00001 to 99. 99999 mm/rev
0.000001 to 99.999999 inch/rev
0.0000001 to 9.9999999 inch/rev 0.0001 to 999.9999 °/rev
0.00001 to 99.99999 °/rev
2nd to 4th reference point
offset (value on machine
coordinate system) ±99999.999 mm
±9999.9999 mm ±9999.9999 inch
±999.99999 inch ±99999.999 °
±9999.9999 °
Tool offset amount (shape) ±999.999 mm
±99.9999 mm
±99.9999 inch
±9.99999 inch
Tool offset amount (wear) ±99.999 mm
±9.9999 mm ±9.9999 inch
±0.99999 inch
Incremental feed amount 0.001 mm/pulse
0.0001 mm/pulse
0.0001 inch/pulse
0.00001 inch/pulse 0.001 °/pulse
0.0001 °/pulse
Handle feed amount 0.001 mm/pulse
0.0001 mm/pulse 0.0001 inch/pulse
0.00001 inch/pulse 0.001 °/pulse
0.0001 °/pulse
Soft limit range
(value on machine
coordinate system) –99999.999 to +99999.999 mm
–9999.9999 to +9999. 9999 mm –9999.9999 to +9999.9999 inch
–999.99999 to +999.99999 inch 1 to 359.999 °
1 to 359.9999 °
Dwell time 0 to 99999.999 s 0 to 99999.999 s
Backlash compensation
amount 0 to ±9999 pulse 0 to ±9999 pulse 0 to ±9999 pulse
Pitch error compensation 0 to ±9999 pulse 0 to ±9999 pulse 0 to ±9999 pulse
M system thread lead (F) 0.001 to 999.999 mm/rev
0.0001 to 99.9999 mm/rev 0.0001 to 39.3700 inch/rev
0.00001 to 3.93700 inch/rev
M system thread lead
(Precise E) 0.00001 to 999.99999 mm/rev
0.000001 to 99.999999 mm/rev 0.000001 to 39.370078 inch/rev
0.000001 to 3.937007 inch/rev
L system thread lead (F) 0.0001 to 999.9999 mm/rev
0.00001 to 99.99999 mm/rev 0.000001 to 99.999999 inch/rev
0.0000001 to 9.9999999 inch/rev
L system thread lead
(Precise E) 0.00001 to 999.99999 mm/rev
0.000001 to 99.999999 mm/rev 0.000010 to 9.9999999 inch/rev
0.0000010 to 0.99999999 inch/rev
(Note 1) The second line in the table applies when the least setting increment is 0.001, 0.0001 from
the first line.
(Note 2) Least input setting increment "C" (0.0001(°)mm/0.00001inch) is a specification for E68
system. This cannot be used with E60.