Keysight DSOX3012T User Manual Download Page 19

Page: 19 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Digital Voltmeter and Counter

Digital Voltmeter / 290
Counter / 291

Frequency Response Analysis

To make connections / 295
To set up and run the analysis / 296
To view and save the analysis results / 298

Waveform Generator

To select generated waveform types and settings / 301
To edit arbitrary waveforms / 305

Creating New Arbitrary Waveforms / 306
Editing Existing Arbitrary Waveforms / 307
Capturing Other Waveforms to the Arbitrary Waveform / 311

To output the waveform generator sync pulse / 312
To specify the expected output load / 312
To use waveform generator logic presets / 313
To add noise to the waveform generator output / 313
To add modulation to the waveform generator output / 314

To set up Amplitude Modulation (AM) / 315
To set up Frequency Modulation (FM) / 316
To set up Frequency-Shift Keying Modulation (FSK) / 317

To restore waveform generator defaults / 318

Save/Email/Recall (Setups, Screens, Data)

Saving Setups, Screen Images, or Data / 321

To save setup files / 323
To save BMP or PNG image files / 324

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands