Keysight DSOX3012T User Manual Download Page 206

Page: 206 / 530

206

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Triggers

When two non-overlapping zones are used, their conditions are ANDed to become

the final qualifying condition.

When two overlapping zones have the must intersect condition, the zones are

ORed. When two overlapping zones have different conditions, Zone 1 takes

precedence and Zone 2 is not used. In this case, Zone 2 will have no fill (that is,

neither solid nor shaded) to indicate that it is not being used.

The zone qualified trigger feature is incompatible with, and will disable, the XY and

Roll horizontal time modes and the Averaging acquisition mode.

NOTE

Keep in mind that the TRIG OUT signal comes from the oscilloscope's hardware trigger. The

TRIG OUT signal indicates when there is a trigger (acquisition) that is evaluated for zone

intersection, not when an acquisition meets the zone qualification and is plotted on the

oscilloscope's display.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands