Keysight DSOX3012T User Manual Download Page 297

Page: 297 / 530

Frequency Response Analysis

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

297

There are settings for:

•

The start and stop frequencies in the sweep, as well as the number of points

per decade.

•

The channels probing the input and output. (Click the help icon to view a

connection diagram.)

•

The waveform generator amplitude and expected output load impedance.

To specify different amplitudes for different decades, select

Amplitude Profile

The output impedance of the Gen Out signal is fixed at 50 ohms. However,

the output load selection lets the waveform generator display the correct

amplitude and offset levels for the expected output load. If the actual load

impedance is different than the selected value, the displayed amplitude and

offset levels will be incorrect.

Click the

Run Analysis

softkey.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands