Keysight DSOX3012T User Manual Download Page 372

Page: 372 / 530

372

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Web Interface

Setting a Password

Whenever you connect the oscilloscope to a LAN, it is good practice to set a

password. The password prevents someone from remotely accessing the

oscilloscope via a Web browser and changing parameters. Remote users can still

view the Welcome screen, view network status, etc., but they can't operate the

instrument or change its setup without the password.

To set a password:

Access the oscilloscope's web interface (see

“Accessing the Web Interface"

page 360).

When the oscilloscope's web interface is displayed, select the Configure

Network tab from the instrument's Welcome page.

Click the

Modify Configuration

button.

Enter your desired password, and click

Apply Changes

Configure

Network

tab

Modify Configuration

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands