Keysight DSOX3012T User Manual Download Page 31

Page: 31 / 530

Getting Started

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Power-On the Oscilloscope

Power

Requirements

Line voltage, frequency, and power:
• ~Line 100-120 Vac, 50/60/400 Hz
• 100-240 Vac, 50/60 Hz
• 100 W max

Ventilation

Requirements

The air intake and exhaust areas must be free from obstructions. Unrestricted air

flow is required for proper cooling. Always ensure that the air intake and exhaust

areas are free from obstructions.

The fan draws air in from the left side and bottom of the oscilloscope and pushes it

out behind the oscilloscope.

When using the oscilloscope in a bench-top setting, provide at least 2" clearance

at the sides and 4" (100 mm) clearance above and behind the oscilloscope for

proper cooling.

Flip-Out Tabs

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands