Keysight DSOX3012T User Manual Download Page 80

Page: 80 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Vertical Controls

The ground level of the signal for each displayed analog channel is identified by
the position of the

icon at the far-left side of the display.

To turn waveforms on or off (channel or math)

Press an analog channel key turn the channel on or off (and to display the

channel's menu).

When a channel is on, its key is illuminated.

You can also do this using the touchscreen. See

“Turn Channels On/Off and

Open Scale/Offset Dialogs"

on page 55.

Channel,
Volts/div

Channel 1
ground
level

Trigger
source

Trigger level
or threshold

Channel 2
ground
level

NOTE

Turning channels off

You must be viewing the menu for a channel before you can turn it off. For example, if channel

1 and channel 2 are turned on and the menu for channel 2 is being displayed, to turn channel

1 off, press

[1]

to display the channel 1 menu; then, press

[1]

again to turn channel 1 off.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands