Keysight DSOX3012T User Manual Download Page 87

Page: 87 / 530

Vertical Controls

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Press the Channel on/off key to turn the channel on (if the channel is off).

In the Channel Menu, press the

Probe

softkey.

In the Channel Probe Menu, the second softkey from the left is for specifying

your probe head (and attenuation). Repeatedly press this softkey until the

probe head selection matches the attenuator you are using.

The choices are:

•

10:1 single-ended browser (no attenuator).

•

10:1 differential browser (no attenuator).

•

10:1 (+6 dB Atten) single-ended browser.

•

10:1 (+6 dB Atten) differential browser.

•

10:1 (+12 dB Atten) single-ended browser.

•

10:1 (+12 dB Atten) differential browser.

•

10:1 (+20 dB Atten) single-ended browser.

•

10:1 (+20 dB Atten) differential browser.

Press the

Calibrate Probe

softkey and follow the instructions on the display.

For more information on InfiniiMax probes and accessories, see the probe's

User's

Guide

NOTE

When calibrating a differential probe, connect the positive lead to the Probe Comp terminal

and the negative lead to the ground terminal. You may need to connect an alligator clip to the

ground lug to allow a differential probe to span between the Probe Comp test point and

ground. A good ground connection ensures the most accurate probe calibration.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands