Keysight DSOX3012T User Manual Download Page 193

Page: 193 / 530

Triggers

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

193

In the Video Trigger Menu, press the

Standard

softkey to set the video standard.

The oscilloscope supports triggering on the following television (TV) and video

standards.

With the DSOX3VID extended video triggering license, the oscilloscope

additionally supports these standards:

Standard

Type

Sync Pulse

NTSC

Interlaced

Bi-level

PAL

Interlaced

Bi-level

PAL-M

Interlaced

Bi-level

SECAM

Interlaced

Bi-level

Standard

Type

Sync Pulse

Generic

Interlaced/Progressive

Bi-level/Tri-level

EDTV 480p/60

Progressive

Bi-level

EDTV 567p/50

Progressive

Bi-level

HDTV 720p/50

Progressive

Tri-level

HDTV 720p/60

Progressive

Tri-level

HDTV 1080p/24

Progressive

Tri-level

HDTV 1080p/25

Progressive

Tri-level

HDTV 1080p/30

Progressive

Tri-level

HDTV 1080p/50

Progressive

Tri-level

HDTV 1080p/60

Progressive

Tri-level

HDTV 1080i/50

Interlaced

Tri-level

HDTV 1080i/60

Interlaced

Tri-level

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands