Keysight DSOX3012T User Manual Download Page 48

Page: 48 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Getting Started

•

Flick — allows very fast browsing of waveforms. It is similar to browsing on

tablets and smartphones. It is much easier to flick than to continually turn a

knob.

•

Drag — drag your finger across the screen to change the horizontal delay.

Drag your finger up or down to change the vertical offset.

To select waveforms, tap them. The waveform closest horizontally to the tap

location is selected. The selected waveform is indicated by the ground marker

with the filled background (channel 1 in the following example).

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands