manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from manualshive.com.

Share
Download
background image

I2C/SPI Triggering and Serial Decode

28

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

447

 

In the SPI Master-Out Slave-In Menu:

a

Press the 

MOSI Data

 softkey; then, turn the Entry knob to select the channel 

that is connected to a SPI serial data line. (If the channel you selected is off, 

switch it on.)

The MOSI label for the source channel is automatically set.

b

Press the 

Threshold

 softkey; then, turn the Entry knob to select the MOSI 

signal threshold voltage level.

The threshold voltage level is used in decoding, and it will become the 

trigger level when the trigger type is set to the selected serial decode slot.

7

(Optional) Press the 

MISO

 softkey to open the SPI Master-In Slave-Out Menu.

In the SPI Master-In Slave-Out Menu:

a

Press the 

MISO Data

 softkey; then, turn the Entry knob to select the channel 

that is connected to a second SPI serial data line. (If the channel you 

selected is off, switch it on.)

The MISO label for the source channel is automatically set.

b

Press the 

Threshold

 softkey; then, turn the Entry knob to select the MISO 

signal threshold voltage level.

The threshold voltage level is used in decoding, and it will become the 

trigger level when the trigger type is set to the selected serial decode slot.

8

Press the 

CS

 softkey to open the SPI Chip Select Menu.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Tascam DP-02 Owner'S Manual preview
DP-02
Brand: Tascam Pages: 80
Tascam DP-01 Specifications preview
DP-01
Brand: Tascam Pages: 2
Walker A10 Operator'S Manual preview
A10
Brand: Walker Pages: 24
JB-Lighting A8 Upgrade Manual preview
A8
Brand: JB-Lighting Pages: 40
Backyard Play Systems 4136 Manual preview
4136
Brand: Backyard Play Systems Pages: 74
Hach MET ONE 3400 Series User Manual preview
MET ONE 3400 Series
Brand: Hach Pages: 48
Jackson DISHSTAR ADA-SEER Operation Manual preview
DISHSTAR ADA-SEER
Brand: Jackson Pages: 2
EuroLite 51930455 User Manual preview
51930455
Brand: EuroLite Pages: 28
Konica Minolta DF-619 Service Manual preview
DF-619
Brand: Konica Minolta Pages: 32
Yamaha MU80 Sound List preview
MU80
Brand: Yamaha Pages: 45
SprotDog Pro hunter 2525 Operating Manual preview
Pro hunter 2525
Brand: SprotDog Pages: 28
Barikell MK8 90 Instructions For Use Manual preview
MK8 90
Brand: Barikell Pages: 32
Ekinex EK-CF2-TP Applications Manual preview
EK-CF2-TP
Brand: Ekinex Pages: 37
HMS LS7849 Manual Instruction preview
LS7849
Brand: HMS Pages: 36
Gardol GRW-E 57 Original Operating Instructions preview
GRW-E 57
Brand: Gardol Pages: 80
Hameg HM 8122 User Manual preview
HM 8122
Brand: Hameg Pages: 39
Teac CD-RW890 Specifications preview
CD-RW890
Brand: Teac Pages: 1
Garelick 31800 Assembly Instructions preview
31800
Brand: Garelick Pages: 2

Brands by name

Popular brands

Load more brands