background image

- BEFORE YOU BEGIN -

Your premium playset is manufactured from wood which has many natural characteristics and blemishes that may be present in some of the pieces in your playset. These natural characteristics may include knots or minor 

cracks/splits. All individual parts have been cut to provide a smooth and safe surface. All parts have been inspected to assure we pack only the safest, most durable wood product. Any minor blemishes in your playset will 

not affect the strength, durability, or structural integrity of the fi nished product. Our limited warranty does not cover the imperfections not resulting in structural failure.

Playset

First...

‰

 

Check with your homeowner’s association before

    assembling.

‰

 

Read instructions thoroughly before you begin. If you

    have purchased accessories to accompany this play
    set, please read all installation instructions before  
    beginning assembly of this structure.

Check All Parts

‰

 

If a part is missing, circle the part in question and call.

Important

‰

 

In a drawing, a dotted line represents a part hidden

    from view (like a part under a panel).

Adult Assistance required

‰

 

Assistance is necessary to handle, 

À

 t

   and secure some components.

  

Squareness is very Important!

Start with a level surface and keep 90° corners and 90° 
perpendiculars throughout the assembly to ensure all 
components fi t together.

Safety!

‰

  

Check for protruding screws and bolts

verify all screw

   and bolt  lengths during assembly.

Always wear OSHA-APPROVED safety 
glasses throughout assembly process.

Tools Required

Socket Set
 
Hammer  

9/16” Combination
    Wrench 

3/16” Allen Wrench

#2 Square Drive
      Bit (included)

#3 Phillips Bit   
 

 

Cordless Drill
   w/Charger

1/8” Drill Bit

7/16” Drill Bit

1/4” Drill Bit

3/8” Drill Bit

Tape Measure 

Level

C - Clamps 
 
6’ Step Ladder

Framing/Speed
Square

   

- BEFORE YOU BEGIN -

Recommended for Ages 3 to 11

Backyard Play Systems

Customer Service

1-866-890-2211

1000 Ternes Drive

Monroe, MI 48162

- NOTICE -

This playset product is not intended for public use. It is intended for 

residential application and is not warranted for public or commercial use.

Model 4136
Model 6259

05/22/2012

2286

Summary of Contents for 4136











































































Reviews: