Backyard Play Systems 4136 Manual Download

Page: 17 / 74

FRAME

ASSEMBLY - A

BOT

TOM

T-Nut

Flat Washer
Lock Washer
3-3/4" Hex Bolt

1. Select 2710-ST from GROUP B (wood parts pages).

2. Align 2710-ST with pre-drilled hole.

FLIP ASSEMBLY-A OVER TO INSTALL SIDE BRACES.

90°

2710-ST

1 x 3-1/2 x 25-3/4"

Ensure all bracing is 90° square before tightening
hex bolts. Do not fully tighten hex bolts at this
time, adjustments may be needed.

Flush with

bottom edge of

frame upright.

C. BORES

TOWARD TOP.

BOT

T-Nut

Flat Washer
Lock Washer
3-3/4" Hex Bolt

3. Select 2710-ST from GROUP B (wood parts pages).

4. Align 2710-ST with pre-drilled hole.

Ensure 2710-ST is 90° square
before tightening hex bolts.

Set Assembly-A aside and
proceed to Assembly-B.

90°

2710-ST

1 x 3-1/2 x 25-3/4"

Flush with

bottom edge of

frame upright.

C. BORES

TOWARD TOP.

Summary of Contents for 4136











































































Search results

Summary of Contents for 4136

Reviews:

Related manuals for 4136

Brands by name

Popular brands

Backyard Play Systems 4136, Manual

Search results

Summary of Contents for 4136

Reviews:

Related manuals for 4136

Brands by name

Popular brands