Keysight DSOX3012T User Manual Download Page 309

Page: 309 / 530

Waveform Generator

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

309

For fine adjustment of the region selection (or to clear the selection), touch the

edit tab, and use the

Selected Region

controls:

To perform points operations, touch the

Operation

controls drop-down, select the

operation, and use the controls for the selected operation:

•

Cut/Copy

selected points regions to the clipboard and

Paste

points from the

clipboard.

When pasting points from the clipboard, you can paste at the beginning, end,

cursor location (currently selected point), or you can replace the currently

selected points region.

•

Insert New

points.

You can specify the number of new points and their voltage.

•

Replace

a selected points region with new points.

•

Delete

a selected points region.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands