Keysight DSOX3012T User Manual Download Page 155

Page: 155 / 530

155

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

9 Display Settings

To adjust waveform intensity / 155
To set or clear persistence / 157
To clear the display / 158
To select the grid type / 158
To adjust the grid intensity / 159
To freeze the display / 159

To adjust waveform intensity

You can adjust the intensity of displayed waveforms to account for various signal

characteristics, such as fast time/div settings and low trigger rates.

Increasing the intensity lets you see the maximum amount of noise and

infrequently occurring events.

Reducing the intensity can expose more detail in complex signals as shown in the

following figures.

Press the

[Intensity]

key to illuminate it.

This key is located just below the Entry knob.

Turn the Entry knob to adjust the waveform intensity.

Waveform intensity adjustment affects analog channel waveforms only (not math

waveforms, reference waveforms, digital waveforms, etc.).

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands