Keysight DSOX3012T User Manual Download Page 266

Page: 266 / 530

266

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Measurements

This measurement is available for analog channels.

Rising Edge Count

The

Rising Edge Count

measurement is an edge count for the selected waveform

source.

This measurement is available for analog channels.

Falling Edges Count

The

Falling Edges Count

measurement is an edge count for the selected waveform

source.

This measurement is available for analog channels.

Mixed Measurements

•

“Area"

on page 266

Area

Area measures the area between the waveform and the ground level. Area below

the ground level is subtracted from area above the ground level.

Negative pulse count

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands