manualshive.com logo in svg

Keysight DSOX3012T, User Manual

The Keysight DSOX3012T is a high-performance digital storage oscilloscope designed for precision measurements in a variety of applications. For detailed instructions on how to utilize all the features and functions of this device, you can download the user manual for free from manualshive.com.

Share
Download
background image

344

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

22

Utility Settings

 

5

Configure the oscilloscope's LAN interface:

a

Use the 

Modify

 softkey (and the other softkeys and keypad entry dialogs) to 

enter the IP Address, Subnet Mask, Gateway IP, and DNS IP values.

b

Press the 

Host name

 softkey and use the keypad entry dialog to enter the 

Host Name.

c

Press the 

Apply

 softkey.

6

Connect the oscilloscope to the local area network (LAN) by inserting the LAN 

cable into the "LAN" port on the rear panel of the oscilloscope.

Stand-alone (Point-to-Point) Connection to a PC

The following procedure describes how to establish a point-to-point (stand alone) 

connection to the oscilloscope. This is useful if you want to control the 

oscilloscope using a laptop computer or a stand-alone computer.

1

Press 

[Utility] > I/O

.

2

Press the 

LAN Settings

 softkey.

3

Press the 

Config

 softkey; then, turn the Entry knob to select 

Automatic

, and press 

the softkey again to enable it.

If your network supports DHCP or AutoIP, enabling 

Automatic

 lets the 

oscilloscope use those services to get its LAN configuration settings

4

Connect your PC to the oscilloscope using a cross-over LAN cable such as 

Keysight part number 5061-0701, available on the web at 

www.keysight.com/find/parts

.

5

Cycle power on the oscilloscope. Wait until the LAN connection is configured:

•

Press 

[Utility] > I/O

 and wait until the LAN status shows "configured".

This may take a few minutes.

Now, the instrument is connected, and the instrument's web interface or remote 

control via LAN may be used.

File Explorer

The File Explorer lets you navigate the oscilloscope's internal file system and the 

file systems of connected USB storage devices.

From the internal file system, you can load oscilloscope setup files or mask files.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSOX3012T

Kapriol 27977 Manufacturer'S Instruction And Information preview
27977
Brand: Kapriol Pages: 32
JABO 4236 Installation Manual preview
4236
Brand: JABO Pages: 4
Eastern Jungle Gym CLASSIC Owner'S Instruction Manual preview
CLASSIC
Brand: Eastern Jungle Gym Pages: 17
Vahle VCL Series Translation Of The Original Operating Instructions preview
VCL Series
Brand: Vahle Pages: 96
Nakayama PS5000 Manual preview
PS5000
Brand: Nakayama Pages: 37
Xo FLEX Installation Instructions Manual preview
FLEX
Brand: Xo Pages: 59
Falcon HT2 Installation And Servicing Instructions preview
HT2
Brand: Falcon Pages: 8
Halyard MIC-KEY Instructions For Use Manual preview
MIC-KEY
Brand: Halyard Pages: 88
HALDER EH 2B353 Short Instruction Manual preview
EH 2B353
Brand: HALDER Pages: 2
Hällde RG-200 User Instructions preview
RG-200
Brand: Hällde Pages: 40
Hällde RG-400i User Instructions preview
RG-400i
Brand: Hällde Pages: 6
Össur bionic power knee Quick Reference Card preview
bionic power knee
Brand: Össur Pages: 2
Össur BALANCE KNEE OM8 Instructions For Use Manual preview
BALANCE KNEE OM8
Brand: Össur Pages: 36
Össur BALANCE FOOT J Instructions For Use Manual preview
BALANCE FOOT J
Brand: Össur Pages: 37
Össur REBOUND DIABETIC WALKER Instructions For Use Manual preview
REBOUND DIABETIC WALKER
Brand: Össur Pages: 63
Össur UNITY Instructions For Use Manual preview
UNITY
Brand: Össur Pages: 67
Électronique du Mazet ECHODIA Babyscreen Instructions For Use And Technical Description preview
ECHODIA Babyscreen
Brand: Électronique du Mazet Pages: 65
DOTLUX FLOOReco 5164-040120 User Manual preview
FLOOReco 5164-040120
Brand: DOTLUX Pages: 10

Brands by name

Popular brands

Load more brands