Keysight DSOX3012T User Manual Download Page 205

Page: 205 / 530

Triggers

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

205

The

[Zone]

key becomes lit to show the zone qualified trigger feature is enabled.

In the Zone Qualified Trigger Menu, press the

Source

softkey and select the

analog channel input source that both zones are associated with.

Zone colors match the selected analog input channel. "Must Not Intersect"

zones are shaded differently than the solid "Must Intersect" zones.

The zone qualified trigger source does not have to be the same as the hardware

trigger source.

You can use the

Zone 1 On

and

Zone 2 On

softkeys to disable or enable zones,

and you can use the

Zone 1

and

Zone 2

softkeys to toggle between the "Must

Intersect" and "Must Not Intersect" conditions.

Disabling both zones disables the zone qualified trigger feature. When the zone

qualified trigger feature is enabled, at least one zone must be enabled.

You can press the

[Zone]

key to disable or re-enable the zone qualified trigger.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands