Keysight DSOX3012T User Manual Download Page 293

Page: 293 / 530

Digital Voltmeter and Counter

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

293

• Press the

Source

softkey and turn the Entry knob to change the analog channel

on which counter measurements are made.

• Press the

Event Slope

softkey to choose whether positive or negative edge

events are counted.

• Press the

Gate

softkey to enable or disable gating of the edge event count using

a positive or negative level on a second analog channel.

When gating is enabled:

Press the

Gate Source

softkey and turn the Entry knob to select the analog

channel that will supply the gating signal.

The selected channel does not have to be on (displaying a waveform).

Press the polarity softkey to choose whether positive or negative levels are

used to gate the edge event count.

The trigger level for the selected analog channel is used to determine the

polarity of the signal.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands