Keysight DSOX3012T User Manual Download Page 135

Page: 135 / 530

Digital Channels

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

135

Acquiring waveforms using the digital channels

When you press

[Run/Stop]

[Single]

to run the oscilloscope, the oscilloscope

examines the input voltage at each input probe. When the trigger conditions are

met the oscilloscope triggers and displays the acquisition.

For digital channels, each time the oscilloscope takes a sample it compares the

input voltage to the logic threshold. If the voltage is above the threshold, the

oscilloscope stores a 1 in sample memory; otherwise, it stores a 0.

To display digital channels using Autoscale

When signals are connected to the digital channels — be sure to connect the

ground leads — Autoscale quickly configures and displays the digital channels.
• To configure the instrument quickly, press the

[Auto Scale]

key.

Figure 21

Example: Autoscale of digital channels (MSO models only)

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands