Keysight DSOX3012T User Manual Download Page 335

Page: 335 / 530

335

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

21 Print (Screens)

To print the oscilloscope's display / 335
To set up network printer connections / 337
To specify the print options / 338
To specify the palette option / 339

You can print the complete display, including the status line and softkeys, to a

USB printer or a network printer when the LAN connection is used.

The Print Configuration Menu is displayed when you press the

[Print]

key. The print

option softkeys and the

Press to Print

softkey are ghosted (not available) until a

printer is connected.

To print the oscilloscope's display

Connect a printer. You can:

•

Connect a USB printer to one of the the USB ports on the front panel or the

rectangular USB host port on the rear panel.

For the most up-to-date listing of printers that are compatible with the

InfiniiVision oscilloscopes, please visit

www.keysight.com/find/InfiniiVision-printers

•

Set up a network printer connection. See

“To set up network printer

connections"

on page 337.

Press the

[Print]

key on the front panel.

In the Print Configuration Menu, press the

Print to

softkey; then, turn the Entry

knob to select the desired printer.

Press the

Options

softkey to select the print options.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands