Keysight DSOX3012T User Manual Download Page 131

Page: 131 / 530

131

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

7 Digital Channels

To connect the digital probes to the device under test / 131
Acquiring waveforms using the digital channels / 135
To display digital channels using Autoscale / 135
Interpreting the digital waveform display / 136
To switch all digital channels on or off / 138
To switch groups of channels on or off / 138
To switch a single channel on or off / 138
To change the displayed size of the digital channels / 137
To reposition a digital channel / 139
To change the logic threshold for digital channels / 138
To display digital channels as a bus / 140
Digital channel signal fidelity: Probe impedance and grounding / 143

This chapter describes how to use the digital channels of a Mixed-Signal

Oscilloscope (MSO).

The digital channels are enabled on MSOX3000T X-Series models and

DSOX3000T X-Series models that have the MSO upgrade license installed.

To connect the digital probes to the device under test

If necessary, turn off the power supply to the device under test.

Turning off power to the device under test would only prevent damage that

might occur if you accidentally short two lines together while connecting

probes. You can leave the oscilloscope powered on because no voltage appears

at the probes.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands