Keysight DSOX3012T User Manual Download Page 11

Page: 11 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

To set up searches / 74
To copy search setups / 74

To navigate time / 75
To navigate search events / 75
To navigate segments / 76

To turn waveforms on or off (channel or math) / 80
To adjust the vertical scale / 81
To adjust the vertical position / 81
To specify channel coupling / 81
To specify channel input impedance / 82
To specify bandwidth limiting / 83
To change the vertical scale knob's coarse/fine adjustment

setting / 83

To invert a waveform / 84
Setting Analog Channel Probe Options / 84

To specify the channel units / 85
To specify the probe attenuation / 85
To specify the probe skew / 86
To calibrate a probe / 86

FFT Spectral Analysis

Searching for FFT Peaks / 93
FFT Measurement Hints / 93
FFT Units / 95
FFT DC Value / 95

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands