Keysight DSOX3012T User Manual Download Page 166

Page: 166 / 530

166

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Labels

To add an annotation

You can add up to four annotations to the oscilloscope's display. Annotations are

useful for documentation purposes, to add notes before capturing screens.

To add an annotation:

Press

[Display]

Label

In the label menu, press

Annotation

In the Annotation Menu, press the

Display

softkey and turn the Entry knob to

select the desired annotation.

Then, press the

Display

softkey again to enable/disable the annotation display.

When enabled, you can drag the annotation anywhere in the graticule using the

touchscreen, a USB mouse, or the

and

softkeys.

Press

Edit

In the Edit keypad dialog, you can enter text using:

•

The touch screen (when the front panel

[Touch]

key is lit).

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands