Keysight DSOX3012T User Manual Download Page 415

Page: 415 / 530

CAN/LIN Triggering and Serial Decode

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

415

With LIN selected as the serial decode mode, press

[Search]

In the Search Menu, press the

Search

softkey; then, turn the Entry knob to select

the serial slot (Serial 1 or Serial 2) on which the LIN signal is being decoded.

Press

Search

; then, select from these options:

•

— Finds frames with the specified ID. Press the Frame ID softkey to select

the ID.

•

ID & Data

— Finds frames with the specified ID and data. Press the Frame ID

softkey to select the ID. Press the Bits softkey to enter the data value.

•

Errors

— Finds all errors.

For more information on searching data, see

“Searching Lister Data"

on page 152.

For more information on using the

[Navigate]

key and controls, see

“Navigating the

Time Base"

on page 75.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands