Keysight DSOX3012T User Manual Download Page 375

Page: 375 / 530

375

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

24 Reference

Specifications and Characteristics / 375
Measurement Category / 375
Environmental Conditions / 377
Probes and Accessories / 378
Loading Licenses and Displaying License Information / 378
Software and Firmware Updates / 380
Binary Data (.bin) Format / 381
CSV and ASCII XY files / 388
Acknowledgements / 390
Product Markings and Regulatory Information / 392

Specifications and Characteristics

Please see the InfiniiVision oscilloscope data sheets for complete, up-to-date

specifications and characteristics. To download a data sheet, please visit:

www.keysight.com/find/3000TX-Series

Measurement Category

•

“Oscilloscope Measurement Category"

on page 375

•

“Measurement Category Definitions"

on page 376

•

“Maximum Input Voltages"

on page 376

Oscilloscope Measurement Category

The InfiniiVision oscilloscopes are not intended to be used for measurements in

Measurement Category II, III, or IV.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands