Keysight DSOX3012T User Manual Download Page 280

Page: 280 / 530

280

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Mask Testing

Mask Statistics

From the Mask Test Menu, press the

Statistics

softkey to enter the Mask Statistics

Menu.

Show Stats

When you enable

Show Statistics

the following information is displayed:

•

Current mask, name of mask, Channel number, date and time.

•

# of Tests (total number of mask tests executed).

•

Status (Passing, Failing, or Untested).

•

Accumulated test time (in hours, minutes, seconds, and tenths of seconds).

And for each analog channel:

•

Number of failures (acquisitions in which the signal excursion went beyond

the mask).

•

Failure rate (percentage of failures).

•

Sigma (the ratio of process sigma to maximum achievable sigma, based on

number of waveforms tested).

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands