Keysight DSOX3012T User Manual Download Page 99

Page: 99 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

5 Math Waveforms

To display math waveforms / 99
To adjust the math waveform scale and offset / 101
Units for Math Waveforms / 101
Math Operators / 102
Math Transforms / 104
Math Filters / 118
Math Visualizations / 121

In addition to the dedicated FFT function (see

Chapter 4

, “FFT Spectral Analysis,”

starting on page 89), you can define two other math functions. One math function

waveform can be displayed at a time. The math function waveform is displayed in

light purple.

Math functions can be performed on analog channels or they can be performed on

lower math functions when using operators other than add, subtract, multiply, or

divide.

To display math waveforms

Press the

[Math]

key on the front panel to display the Waveform Math Menu.

Press the

Display Math

softkey and turn the Entry knob to select the math

function you want to display. Then, either push the Entry knob or press the

Display Math

softkey again to display the selected math function.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands