Keysight DSOX3012T User Manual Download Page 46

Page: 46 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Getting Started

•

“Enter Names Using Alpha-Numeric Keypad Dialogs"

on page 52

•

“Change Waveform Offsets By Dragging Ground Reference Icons"

on page 53

•

“Access Controls and Menus Via the Menu Icon"

on page 54

•

“Turn Channels On/Off and Open Scale/Offset Dialogs"

on page 55

•

“Access the Horizontal Menu and Open the Scale/Delay Dialog"

on page 56

•

“Access the Trigger Menu, Change the Trigger Mode, and Open the Trigger

Level Dialog"

on page 57

•

“Use a USB Mouse and/or Keyboard for Touchscreen Controls"

on page 58

Draw Rectangles for Waveform Zoom or Zone Trigger Set Up

Touch the upper-right corner to select the rectangle draw mode.

Drag your finger across the screen to draw a rectangle.

Take your finger off the screen.

Touch the desired option from the popup menu.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands