Keysight DSOX3012T User Manual Download Page 14

Page: 14 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

To display digital channels as a bus / 140
Digital channel signal fidelity: Probe impedance and

grounding / 143
Input Impedance / 143
Probe Grounding / 145
Best Probing Practices / 147

Serial Decode Options / 149
Lister / 151
Searching Lister Data / 152

To adjust waveform intensity / 155
To set or clear persistence / 157
To clear the display / 158
To select the grid type / 158
To adjust the grid intensity / 159
To freeze the display / 159

Labels

To turn the label display on or off / 161
To assign a predefined label to a channel / 162
To define a new label / 163
To load a list of labels from a text file you create / 164
To reset the label library to the factory default / 165
To add an annotation / 166

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands