Keysight DSOX3012T User Manual Download Page 161

Page: 161 / 530

161

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

10 Labels

To turn the label display on or off / 161
To assign a predefined label to a channel / 162
To define a new label / 163
To load a list of labels from a text file you create / 164
To reset the label library to the factory default / 165
To add an annotation / 166

You can define labels and assign them to each analog input channel, or you can

turn labels off to increase the waveform display area. Labels can also be applied to

digital channels on MSO models.

To turn the label display on or off

Press

[Display]

Label

Press the

Display Labels

softkey to turn the label display on.

This turns on labels for the displayed waveforms. Labels are displayed at the

left edge of the displayed traces.

The figure below shows an example of displayed labels.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands