Keysight DSOX3012T User Manual Download Page 224

Page: 224 / 530

224

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Acquisition Control

Using Peak Detect Mode to Find a Glitch

Connect a signal to the oscilloscope and obtain a stable display.

To find the glitch, press the

[Acquire]

key; then, press the

Acq Mode

softkey until

Peak Detect

is selected.

Press the

[Display]

key then press the

∞

Persistence

(infinite persistence) softkey.

Infinite persistence updates the display with new acquisitions but does not

erase previous acquisitions. New sample points are shown at normal intensity

while previous acquisitions are displayed at reduced intensity. Waveform

persistence is not kept beyond the display area boundary.

Press the

Clear Display

softkey to erase previously acquired points. The display

will accumulate points until

∞

Persistence

is turned off.

Characterize the glitch with Zoom mode:

Press the

zoom key (or press the

[Horiz]

key and then the

Zoom

softkey).

To obtain a better resolution of the glitch, expand the time base.

Figure 38

Sine With Glitch, Peak Detect Mode

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands