Keysight DSOX3012T User Manual Download Page 317

Page: 317 / 530

Waveform Generator

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

317

When the modulating signal is at its maximum amplitude, the output frequency

is the carrier signal frequency plus the deviation amount, and when the

modulating signal is at its minimum amplitude, the output frequency is the

carrier signal frequency minus the deviation amount.

The frequency deviation cannot be greater than the original carrier signal

frequency.

Also, the sum of the original carrier signal frequency and the frequency

deviation must be less than or equal to the maximum frequency for the selected

waveform generator function plus 100 kHz.

The following screen shows an FM modulation of a 100 kHz sine wave carrier

signal.

To set up Frequency-Shift Keying Modulation (FSK)

In the Waveform Generator Modulation Menu (under

[Wave Gen] > Settings >

Modulation

Press the

Type

softkey and turn the Entry knob to select

Frequency-Shift Keying

Modulation (FSK)

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands