![background image](http://html1.mh-extra.com/html/ducati/2006-monster-s2r-1000/2006-monster-s2r-1000_workshop-manual_2537598528.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Impianto elettrico
Electric system
sezione / section
P 9
68
Monster S2R 1000
- M.Y. 2006 - edizione/edition 00
La misura di resistenze e di
continuità elettrica
Le misure di resistenze devono essere
effettuate solo quando l'elemento
elettrico o la sezione dell'impianto non
è alimentato ed è isolato dall'impianto
elettrico principale (cioè non collegato
all'impianto elettrico principale).
Queste misure possono essere
utilizzate per verificare la resistenza di
alcuni sensori. Ad esempio dopo aver
scollegato la connessione elettrica del
sensore dei giri/fase dell'impianto di
accensione - iniezione (affacciato
all'ingranaggio di comando dell'albero
della distribuzione), è possibile
verificare la sua resistenza interna,
collegando il multimentro ai suoi
terminali. In questo modo si verifica se
l'avvolgimento interno al sensore è
interrotto (caso in cui la resistenza è
infinita). La misura della resistenza può
essere utilizzata anche per controllare
la continuità di tratti dell'impianto
elettrico o di interruttori e relè. Per
verificare ad esempio l'integrità di una
sezione di impianto elettrico tra due
connessioni, occorre scollegare le
connessioni stesse, collegare i
terminali del multimetro alle due
estremità del cavo elettrico e verificare
il valore di resistenza indicato. Se
questo valore è prossimo allo zero
(inferiore a circa 0,3 ohm) allora il cavo
non è interrotto. Alcuni strumenti
hanno anche una indicazione sonora
che si attiva quando la resistenza si
avvicina al valore zero.
Identica procedura deve essere
seguita per verificare se ad esempio i
due contatti di un interruttore (relè o
manuale) si chiudono regolarmente.
Occorre collegare i terminali del
multimetro a quelli dell'interruttore,
verificando che il valore di resistenza
sia prossimo allo zero (o ascoltando il
segnale sonoro) quando l'interruttore
viene chiuso.
Quando i contatti si aprono la
resistenza indicata dovrà invece
essere infinita.
Per verificare che il multimetro in
modalità “controllo continuità
elettrica” funzioni correttamente,
bisogna cortocircuitare i suoi due
terminali. Il valore di resistenza indicato
dovrà essere praticamente nullo e
dovrà attivarsi il segnale sonoro.
Measurement of resistance
values and electrical continuity
Resistance measurements must be
taken only when the electrical device
or section of the circuit is not powered
and isolated from the main electrical
system (i.e. not connected to the
main electrical system). These
measurements can be utilised to
check the resistance value across
several sensors. For example, after
disconnecting the electrical wiring to
the rpm/ignition - injection system
timing sensor (in front of the camshaft
drive gear) the relative internal
resistance can be checked by
connecting a multimeter to its
terminals. This makes it possible to
check the electrical continuity of the
winding inside the sensor (a reading of
infinite resistance indicates that the
winding is interrupted). Resistance
measurement can also be used to
check the continuity of sections of the
electrical circuit or relay type switches.
For example, to check the condition of
a section of the electrical circuit
between two connections, disconnect
the connections and connect the
terminals of the multimeter to the
ends of the electrical cable in question
to check that the specified resistance
value is present. If this value is close to
zero (i.e. lower than approximately
0.3 ohm) this means that the cable is
not interrupted. Some instruments
feature an audible signal that is
emitted when the resistance
approaches a value of zero.
The same procedure must be
adopted to check whether, for
example, two contacts of a switch
(relay or manual type) are making
the contact correctly when closed.
In this case the terminals of the
multimeter must be connected to
the switch terminals, checking that
the resistance value is close to zero
(or listening for the audible signal)
when the switch is closed.
When the contacts open, the
resistance reading should be infinity.
To check that the multimeter is
functioning correctly in “electrical
continuity test” mode, short out the
two test probes. The resistance value
indicated must be almost nil and the
audible signal must be activated.
Summary of Contents for 2006 Monster S2R 1000
