![background image](http://html1.mh-extra.com/html/ducati/2006-monster-s2r-1000/2006-monster-s2r-1000_workshop-manual_2537598210.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Ruote - Sospensioni - Freni
Wheels - Suspensions - Brakes
sezione / section
G 7
46
Monster S2R 1000
- M.Y. 2006 - edizione/edition 00
Disassembly and
overhaul of the
monoshock tie-rod
Unscrew and remove the upper
bolt (1), the cap (
20
), the lower
bolt (17) and the bush (18).
Remove the tie-rod assembly (11).
The tie–rod assembly (11) is comprised
of a central rod (9) two nuts (10)
and (12) and two ball joints (9) and (13).
Two mounting collars (8) are located
at the sides of each ball joint.
After removing the collars, check the
amount of play in the ball joint by
turning the internal ring by hand:
change the ball joint if it has
excessive play.
During reassembly, note that the
nut (12) marked (A) has a left hand
thread
: on reassembly, note that
this nut is to be fitted to the end of
the rod (11) also marked (A).
The centre-to-centre distance between
the ball joints should be
261
mm.
Altering this distance will affect the
rear ride height of the motorcycle.
Tighten the nuts (10) and (12) on
the central rod (1) to the specified
torque (Sect. C 3).
Smontaggio e revisione
tirante ammortizzatore
Svitare e rimuovere la vite
superiore (1), il tappo (
20
), la vite
inferiore (17) e la boccola (18).
Smontare il tirante completo (11).
Il tirante (11) è composto da un’asta
centrale, da due dadi (10) e (12) e
da due snodi sferici (9) e (13). Sugli
snodi, in corrispondenza del foro di
fulcraggio, lavorano due bussole (8).
Dopo aver rimosso le bussole (8)
verificare, ruotando a mano l’anello
interno, il gioco dello snodo sferico: in
caso di gioco eccessivo sostituirlo.
Durante le operazioni di
ricomposizione fare attenzione al
dado (12) con filettatura sinistrorsa
,
riconoscibile dalla segnatura (A): va
montato in corrispondenza della parte
segnata (A) dell’asta centrale (11).
L’interasse tra gli snodi deve essere
261
mm.
Modificando questa quota si modifica
l’assetto della moto.
Serrare i dadi (10) e (12) sull’asta
centrale (11) alla coppia prescritta
(Sez. C 3).
261mm
12
13
A
11
10
9
8
1
8
9
10
11
8
19
12
13
A
8
18
17
Summary of Contents for 2006 Monster S2R 1000
