A
B
C
D
E
F
G
H
L
M
N
P
Mototelaio
Frame
sezione / section
H 2
9
Monster S2R 1000
- M.Y. 2006 - edizione/edition 00
Rimontaggio componenti
cannotto di sterzo
Importante
I cuscinetti (
5
) e (
6
) del
cannotto sono uguali ma è
necessario evitare assolutamente
di scambiarne i componenti.
Pulire accuratamente e lubrificare
con grasso prescritto le superfici di
contatto.
Per il montaggio degli anelli esterni (C)
dei cuscinetti (
5
) e (
6
) sul cannotto
del telaio è necessario disporre
dell'attrezzo
88713.1062
; procedere
nel modo seguente:
scaldare il cannotto a
150 °C
;
posizionare correttamente gli anelli
esterni (C) nelle sedi del cannotto;
inserire nell'anello inferiore la bussola
fissa (E, quella con foro filettato)
dell'attrezzo;
inserire nell'estremità superiore
dell'asta dell'attrezzo, l'altra bussola
mobile (F) e portarla in battuta
sull'anello del cuscinetto superiore;
avvitare il dado (G) e con chiave
portare in battuta gli anelli esterni (C)
sul cannotto del telaio;
lasciare montato l'attrezzo fino al
raffreddamento del cannotto per
garantire l'appoggio dei cuscinetti
nelle sedi.
Inserire nel perno di sterzo (D) la
rosetta (8) l'anello di tenuta (7) (con il
bordino rivolto verso l'alto) e l’anello
interno (A) del cuscinetto inferiore (
6
),
dopo averlo scaldato per circa 10 minuti
ad una temperatura di
120 °C
.
Inserire nel perno di sterzo il tampone
cod.
88713.1072
. Premere l’anello
interno (A) sull'anello di tenuta (7),
esercitando, manualmente, una certa
pressione per almeno 10 -15 secondi.
Lubrificare con grasso prescritto
l’anello interno (A).
Inserire nel perno di sterzo (D) la
corona di sfere (B) con il lato di
diametro inferiore della gabbia,
rivolto verso l'alto e ingrassarla.
Inserire il perno di sterzo, all'interno
del cannotto portandolo assialmente
in appoggio.
Refitting the steering
head components
Important
The steering head bearings (
5
)
and (
6
) are identical but in no case
may their components be swapped
around during reassembly.
Clean all contact surfaces and lubricate
with the recommended grease.
To fit the outer races (C) of the
bearings (
5
) and (
6
) to the steering
head, use the special tool part
no.
88713.1062
and proceed as
follows:
heat the steering head to
150 °C
;
fit the outer races (C) in their seats
on the steering head;
fit the fixed bush (E, with threaded
hole) of the tool into the lower race;
Fit the other movable bush (F) into the
upper end of the tool and drive it fully
home against the upper bearing race.
Tighten the nut (G) and use a wrench
to seat the outer rings (C) fully in the
steering head;
Leave the tool assembled until the
steering head has cooled down to
ensure that bearings are properly
seated.
Install the washer (8), the oil seal (7)
(with lip uppermost) and the inner
race (A) of the lower bearing (
6
) on
the steering stem (D), after having
heated it for around 10 minutes to
a temperature of
120 °C
.
Fit onto the steering stem the drift
part no.
88713.1072
. Applying manual
pressure, keep the inner ring (A)
pressed against the oil seal (7) for at
least 10-15 seconds.
Lubricate inner bearing ring (A) with
the recommended grease.
Fit the ball race (B) to the steering
stem (D) with the smaller diameter
of the cage facing upwards and
grease the ball race.
Insert the steering stem in steering
head and push it until it becomes
axially seated.
C
A
88713.1062
C
G
F
E
88713.1072
B
A
7
8
A
7
8
A
Summary of Contents for 2006 Monster S2R 1000
