![background image](http://html1.mh-extra.com/html/ducati/2006-monster-s2r-1000/2006-monster-s2r-1000_workshop-manual_2537598499.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Impianto elettrico
Electric system
sezione / section
P 3
39
Monster S2R 1000
- M.Y. 2006 - edizione/edition 00
Teleruttore avviamento
Il teleruttore avviamento (1) è fissato
elasticamente al telaio.
Scollegare la batteria (Sez. P 2).
Rimuovere il teleruttore avviamento
dal proprio alloggiamento.
Svitare i dadi (4) facendo attenzione
alle rosette elastiche (3).
Rimuovere il cavo (2) teleruttore-
motorino avviamento.
Rimuovere il cavo (5) teleruttore-
batteria.
Scollegare il connettore (2) del
teleruttore avviamento dal cablaggio.
Controllo funzionalità
teleruttore avviamento
Applicare una tensione di
12V
(batteria) ai due terminali (A) Positivo
e (B) Negativo del connettore.
Con un multimetro collegato fra i
due poli (perni filettati) (C) e (D) del
teleruttore verificare la presenza
della continuità elettrica (Sez. P 9).
Se non è presente continuità
elettrica, sostituire il teleruttore.
Durante il rimontaggio, verificare che
i poli (C) e (D) non siano ossidati e
applicare spray idrorepellente.
Serrare i dadi (4) alla coppia
prescritta (Sez. C 3).
Rimontare il connettore (2) al
cablaggio.
Starter contactor
Starter motor contactor (1) is
elastically mounted to the battery
mount.
Disconnect the battery (Sect. P 2).
Remove the starter contactor from
its seat.
Unscrew nuts (4), paying attention
to the spring washers (3).
Remove starter motor - contactor
cable (2).
Remove starter motor contactor-
battery cable (5).
Disconnect connector (2) of the
engine start contactor from its wiring.
Checking operation of the
starter motor contactor
Apply
12V
(battery voltage) across
the positive terminal (A) and negative
terminal (B) of the connector.
With a multimeter connected
between the two poles (threaded
studs) (C) and (D) of the contactor,
check for electrical continuity
(Sect. P 9). If there is no electrical
continuity, renew the contactor.
During the reassembly procedure,
ensure that studs (C) and (D) are not
oxidized; apply water repellent spray.
Tighten nuts (4) to the specified
torque (Sect. C 3).
Connect connector (2) to the wiring.
1
12V
A
B
1
1
3
3
2
C
D
1
5
2
+
-
Summary of Contents for 2006 Monster S2R 1000
