![background image](http://html1.mh-extra.com/html/ducati/2006-monster-s2r-1000/2006-monster-s2r-1000_workshop-manual_2537598360.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Motore
Engine
sezione / section
N 4.4
54
Monster S2R 1000
- M.Y. 2006 - edizione/edition 00
Sostituzione della sede valvola
Togliere le sedi usurate fresando
gli anelli. Prestare la massima
attenzione al fine di non danneggiare
l’alloggiamento sulla testa.
Controllare il diametro degli
alloggiamenti sulla testa e scegliere la
sede valvola maggiorata considerando
che l’interferenza di montaggio
dovrà essere
0,11÷0,16
mm. Le sedi
valvola sono fornite a ricambio con
maggiorazione sul diametro esterno
di
0,03 e 0,06
mm.
Scaldare lentamente ed
uniformemente la testa ad una
temperatura di
180
°C
e raffreddare
le sedi con ghiaccio secco.
Piantare le sedi perfettamente in
quadro nel proprio alloggiamento
utilizzando un battitore appropriato.
Lasciare raffreddare e quindi
procedere alla fresatura delle sedi,
al raccordo dei condotti con le sedi
nuove e alla smerigliatura delle valvole.
Accoppiamento valvola -
sede valvola
Verificare, mediante blu di Prussia o
miscela di minio e olio, che la superficie
di contatto (W) tra valvola e sede
risulti di
1,0÷1,5
mm.
Limite massimo ammesso:
2,0
mm
Qualora la quota rilevata fosse
maggiore di quella indicata, procedere
alla ripassatura della sede.
Verificare, riempiendo le canalizzazioni
di aspirazione e scarico di carburante,
che non vi siano perdite; se così fosse,
controllare che non vi siano sbavature
sulle superfici coinvolte nella tenuta.
Changing the valve seat
Remove the worn seats. Mill the
rings. Mill carefully to avoid any
damage to head bores.
Check diameter of head bores and
choose the oversized valve seat
that will give an interference fit of
0.11-0.16
mm. Spare valve seats
are available with outer diameter
oversized by
0.03 and 0.06
mm.
Heat the head gradually and evenly
up to
180
°C
and chill the new valve
seats in dry ice.
Drive the seats perfectly square into
the head bores using a suitable drift.
Allow the cylinder head to cool and
then mill the seats, connect the
oilways with the new seats and
grind the valves.
Mating of valve - valve seat
Use Prussian blue or a mixture of
minium and oil to check that the
contact surface (W) between
valve and seat is
1.0-1.5
mm.
Maximum permissible limit:
2.0
mm
Grind seat if dimension measured is
greater than above limit.
Fill the intake and exhaust ducts
with fuel to check for leaks; if
leaks are present check for the
possible presence of burr on the
sealing surfaces.
W
45˚
Summary of Contents for 2006 Monster S2R 1000
