background image

 

 

 

Important Cautions 

 
 

About running-in of a motorcycle 

The first 1000 km operation is very important in the entire 

service life of a motorcycle. A correct running-in can guarantee 
both  the  longest  service  life  and  the  best  performance  of  the 
vehicle.  Running-in  can  polish  machined  surfaces  and  form 
smooth engagement.   

Careful  and  patient  running-in  can  make  the  motorcycle 

stable  in  driving  and  give  a  full  play  to  its  excellent 
performance. It is important not to do any operation that may 
cause overheat to engine components.   

For  specific  running-in  method,  please  refer  to 

"Running-in of a new vehicle".   

Please  carefully  read  the  manual  and  strictly  observe  all 

instructions or descriptions.   

Special attention shall be paid to the contents emphasized 

with the terms of "warning" "caution" and "note", etc.   

Warning

……

It  concerns with  personal  safety.  Ignoring  it 

may result in accident.   

Precaution

……

It refers to operational methods that must 

be followed or measures that should be taken, so as to prevent 
damage.   

Note

… …

It  refers  to  special  explanations  to  make 

maintenance or important descriptions more explicit.   

The  operation  manual  shall  be  deemed  as  a  permanent 

document  of  the  motorcycle.  When  transfer  the  vehicle  to 
others,  the  instruction  manual  shall  also  be  transferred  to  the 
new owner.

Summary of Contents for QM125-2X GS

















































Reviews: