manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

WARNING!

•

Use only refrigerants and compressor lubricants
approved by the manufacturer for your air condi-
tioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer to
Section 3 of the Warranty Information book for
further warranty information.

•

The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced technician.

Refrigerant Recovery and Recycling
R-134a Air Conditioning Refrigerant is a hydrofluoro-
carbon (HFC) that is endorsed by the Environmental
Protection Agency and is an ozone-saving product. How-
ever, the manufacturer recommends that air conditioning
service be performed by authorized dealers or other
service facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C System

Sealers, Stop Leak Products, Seal Conditioners, Compres-
sor Oil, and Refrigerants.

A/C AIR FILTER — IF EQUIPPED

Refer to the “Maintenance Schedule” in Section 8 of this
manual for A/C Air Filter service intervals.

WARNING!

Do not remove the A/C Air Filter while the blower is
operating or personal injury may result.

MAINTAINING YOUR VEHICLE

383

7

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Brand: Monacor Pages: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Brand: Jeep Pages: 338
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Brand: Farad Pages: 8
XTC ATS-POL-GBU Manual preview
ATS-POL-GBU
Brand: XTC Pages: 4
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Brand: Gatorback Mudflaps Pages: 4
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Brand: Veigel Pages: 24
Cellular Line interphone Instruction Manual preview
interphone
Brand: Cellular Line Pages: 25
Quadratec 16053.5300 Installation Manual preview
16053.5300
Brand: Quadratec Pages: 6
Flash Cover MN019 Instructions preview
MN019
Brand: Flash Cover Pages: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Brand: Porsche Pages: 98
Thule 145012 Quick Start Manual preview
145012
Brand: Thule Pages: 2
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Brand: Mobridge Pages: 20
iSimple blustream Owner'S Manual preview
blustream
Brand: iSimple Pages: 12
Westfalia 17 56 46 Instruction Manual preview
17 56 46
Brand: Westfalia Pages: 2
Gator ARV43M Instruction Manual preview
ARV43M
Brand: Gator Pages: 5
Stanley GLPS Instruction Manual preview
GLPS
Brand: Stanley Pages: 6
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Brand: chinavasion Pages: 3

Brands by name

Popular brands

Load more brands