Dodge 2008 Avenger Owner'S Manual Download Page 142 | Manualshive

Page: 142 / 467

background image

ELECTRONIC SPEED CONTROL — IF EQUIPPED

When engaged, this device takes over the accelerator
operation at speeds greater than 25 mph (40 km/h).

The Speed Control Lever is located on the right side of
the steering wheel.

To Activate:

Push in and release the ON/OFF button located in the
end of the Electronic Speed Control Lever. The Speed
Control indicator in the instrument cluster will illumi-
nate. To turn the system OFF, push in and release the
ON/OFF button a second time. The Speed Control
indicator will turn off. The system should be turned OFF
when not in use.

NOTE:

The Electronic Speed Control System will auto-

matically turn itself off when the ignition key is turned to
the LOCK position.

Speed Control Location

140

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
140
141
142
143
144
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Titanium Series

Brand: Fass Pages: 13

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 2

Brand: Yakima Pages: 12

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: Gator Pages: 2

Polaris TATOU 4S

Brand: Camoplast Pages: 13

Brand: Nav TV Pages: 4

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: MULTILIFT Pages: 62

Brand: Skoda Pages: 324

1995 Cutlass Supreme

Brand: Oldsmobile Pages: 340

Brand: iSimple Pages: 8

Brand: Menabo Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands