manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

TRAILER TOWING

In this section, you will find safety tips and information
on limits to the type of towing you can reasonably do
with your vehicle. Before towing a trailer, carefully
review this information to tow your load as efficiently
and safely as possible.

To maintain warranty coverage, follow the requirements
and recommendations in this manual concerning ve-
hicles used for trailer towing.

If you have any questions or concerns after reviewing
this section, please consult your dealer to for full details
on the towing capabilities of the vehicle.

Common Towing Definitions

The following trailer towing related definitions will assist
you in understanding the following information:

Gross Vehicle Weight Rating (GVWR)
The GVWR is the total allowable weight of your vehicle.
This includes driver, passengers, cargo, and tongue
weight. The total load must be limited so that you do not
exceed the GVWR.

Gross Trailer Weight (GTW)
The GTW is the weight of the trailer plus the weight of all
cargo, consumables and equipment (permanent or tem-
porary) loaded in or on the trailer in its

9

loaded and

ready for operation

9

condition. The recommended way to

measure GTW is to put your fully loaded trailer on a
vehicle scale. The entire weight of the trailer must be
supported by the scale.

Gross Combination Weight Rating (GCWR)
The GCWR is the total permissible weight of your vehicle
and trailer when weighed in combination. (Note that
GCWR ratings include a 150 lbs (68 kg) allowance for the
presence of a driver).

334

STARTING AND OPERATING

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Lancia Delta Owner'S Handbook Manual preview
Delta
Brand: Lancia Pages: 276
T-Tech TT100 User Manual preview
TT100
Brand: T-Tech Pages: 38
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Jabra SP200 - QUICKSTART GUIDE 1 Quick Start Manual preview
SP200 - QUICKSTART GUIDE 1
Brand: Jabra Pages: 2
Jabra BT150 - Headset - Over-the-ear Quick Start Manual preview
BT150 - Headset - Over-the-ear
Brand: Jabra Pages: 2
Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Brand: Jeep Pages: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Brand: Jeep Pages: 6
GARO ENTITY PRO Installation preview
ENTITY PRO
Brand: GARO Pages: 2
B-Speech Sima User Manual preview
Sima
Brand: B-Speech Pages: 4
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Brand: SCC Pages: 4
Subaru Impreza 2.5GT Specifications preview
Impreza 2.5GT
Brand: Subaru Pages: 2
Subaru 1999 Impreza Owner'S Manual preview
1999 Impreza
Brand: Subaru Pages: 328
ACV 281178-28G-M Installation Manual preview
281178-28G-M
Brand: ACV Pages: 2
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Brand: Abrams Pages: 12
Scania Interlock 700 Series Instructions For Use Manual preview
Interlock 700 Series
Brand: Scania Pages: 82
Mercedes-Benz Vito Taxi 2011 Operation Manual preview
Vito Taxi 2011
Brand: Mercedes-Benz Pages: 10
rough country RCH5100 Installation Instructions preview
RCH5100
Brand: rough country Pages: 4

Brands by name

Popular brands

Load more brands