manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

WARNING!

A hot engine cooling system is dangerous. You or
others could be badly burned by steam or boiling
coolant. You may want to call a service center if your
vehicle overheats. If you decide to look under the
hood yourself, refer to Section 7, Maintenance, of this
manual. Follow the warnings under the Cooling
System Pressure Cap paragraph.

ENGINE OIL OVERHEATING (2.4L ENGINE ONLY)
— IF EQUIPPED

During sustained high-speed driving or trailer tow up
long grades on a hot day, the engine oil temperature may
become too hot. If this happens, the “HOTOIL” message
flashes in the odometer and the vehicle speed will be
reduced to 53 mph (85 km/h) until the engine oil
temperature is reduced.

NOTE:

The vehicle speed is reduced to a maximum of

53 mph (85 km/h). You may of course, reduce your
vehicle speed further if needed.

JACKING AND TIRE CHANGING

WARNING!

•

Getting under a jacked-up vehicle is dangerous.
The vehicle could slip off the jack and fall on you.
You could be crushed. Never get any part of your
body under a vehicle that is on a jack. If you need
to get under a raised vehicle, take it to a service
center where it can be raised on a lift.

•

The jack is designed to use as a tool for changing
tires only. The jack should not be used to lift the
vehicle for service purposes. The vehicle should
be jacked on a firm level surface only. Avoid ice or
slippery areas.

350

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Jabra SP200 - QUICKSTART GUIDE 1 Quick Start Manual preview
SP200 - QUICKSTART GUIDE 1
Brand: Jabra Pages: 2
Jabra BT150 - Headset - Over-the-ear Quick Start Manual preview
BT150 - Headset - Over-the-ear
Brand: Jabra Pages: 2
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Brand: Toyota Pages: 19
Daewoo RACER 1998 Electrical Wiring Diagram preview
RACER 1998
Brand: Daewoo Pages: 68
Hyundai Getz 2004 Owner'S Manual preview
Getz 2004
Brand: Hyundai Pages: 437
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Brand: Wagan Pages: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Brand: Chevrolet Pages: 50
Boyo VTL17LTJ Manual preview
VTL17LTJ
Brand: Boyo Pages: 9
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Brand: Chevrolet Pages: 428
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Brand: Mobility Networks Pages: 52
LXE Akerstroms Tx700 Configuration Manual preview
Akerstroms Tx700
Brand: LXE Pages: 146
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Brand: Cadillac Pages: 529
Toro 07389 Installation Instructions Manual preview
07389
Brand: Toro Pages: 16

Brands by name

Popular brands

Load more brands