manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L
Engines
SAE 5W-20 engine oil is recommended for all operating
temperatures. This engine oil improves low temperature
starting and vehicle fuel economy. Your engine oil filler
cap also shows the recommended engine oil viscosity for
your vehicle.

The engine oil filler cap also shows the recommended
engine oil viscosity for your engine. For information on
engine oil filler cap location, refer to the “Engine Com-
partment” illustration in this section.

Lubricants which do not have both the engine oil certi-
fication mark and the correct SAE viscosity grade num-
ber should not be used.

Engine Oil Viscosity (SAE Grade) — 3.5L Engine
SAE 10W-30

engine oil is preferred for all operating

temperatures. The engine oil filler cap also shows the
recommended engine oil viscosity for your vehicle.

Lubricants which do not have both, the engine oil certi-
fication mark and the correct SAE viscosity grade num-
ber should not be used.

The engine oil filler cap also shows the recommended
engine oil viscosity for your engine. For information on
engine oil filler cap location, refer to the “Engine Com-
partment” illustration in this section.

Lubricants which do not have both, the engine oil certi-
fication mark and the correct SAE viscosity grade num-
ber should not be used.

Synthetic Engine Oils
You may use synthetic engine oils provided the recom-
mended oil quality requirements are met, and the recom-
mended maintenance intervals for oil and filter changes
are followed.

MAINTAINING YOUR VEHICLE

377

7

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Code 3 21 COVERT Series Installation And Operation Instructions Manual preview
21 COVERT Series
Brand: Code 3 Pages: 16
TBC DPI1K User Manual preview
DPI1K
Brand: TBC Pages: 12
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Brand: Rightline Gear Pages: 2
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Brand: Tessera4x4 Pages: 20
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Brand: IBASE Technology Pages: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Brand: Modifry Products Pages: 2
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Brand: RAM Pages: 174
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Brand: Ranger design Pages: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Brand: AUTOTECH Pages: 1
Yutrax TX107 Operator'S Manual preview
TX107
Brand: Yutrax Pages: 8
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Brand: Rostra Pages: 2
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Brand: Roadmaster Pages: 4
Toyota 2012 Sienna Owner'S Manual preview
2012 Sienna
Brand: Toyota Pages: 779
SkyRack SR-CB-101 Assembly And Instruction Sheet preview
SR-CB-101
Brand: SkyRack Pages: 2
Waeco MagicWatch MW150 Installation And Operating Manual preview
MagicWatch MW150
Brand: Waeco Pages: 144

Brands by name

Popular brands

Load more brands